Water and utilities
From the reservoir to the consumer’s meter.
Ilonnati controllers on the valves, pumps and reservoirs already in the network, meters at the connections, and IoTyX to see and run all of it: on the web, on a phone and in a control room.
- In the field
- Controllers, valve actuators and SIWaM meters
- On the screen
- Network map, alerts and remote control
- To start
- A pilot on part of the network
IoTyX for water and utilities. An illustration with sample data, not a screenshot.
In short
For a water board or utility, Ilonnati fits a controller beside each valve, pump and reservoir it is asked to run, and meters at the connections. Level, flow, pressure and quality reach IoTyX as they are measured. Operators open and close valves and start pumps from the control room or a phone, and the controller confirms each command. Unusual flow or pressure raises an alert, so leaks, bursts and theft can be found early. Water is Ilonnati’s largest area of work today.
Who it is for
- Water boards and municipal corporations
- Town and rural water schemes
- Housing communities and campuses with their own supply
- Industries that draw and treat their own water
Today, and with Ilonnati
The same jobs, side by side: as they are usually done today, and as they run with Ilonnati.
Today
- Valves are opened and closed by crews travelling to each one.
- Reservoir levels are read on site, or noticed when a tank overflows or runs dry.
- A leak shows up as a complaint or a wet road, long after it started.
- Pumps run to a habit, whether the tank needs water or not.
- Consumption is estimated, so losses cannot be traced to a zone.
With Ilonnati
- Valves open, close and run to a schedule from the control room, and the controller confirms each change.
- Each connected reservoir and tank reports its level as it changes.
- Unusual flow or pressure raises an alert by push notification, email and in the app.
- Pumps start and stop by level or timetable, which prevents overflow and dry running.
- Meters show where the water goes, zone by zone.
A day on the network
6 steps on one platform. Each names the module it uses.
- 01
Readings arrive
Level, flow, pressure and quality from each site reach IoTyX through the controller beside the equipment.
Network monitoring - 02
The network on one map
Zones, mains, valves and reservoirs on a GIS map, each with its live reading.
Network map - 03
A reading crosses its limit
Pressure on a main drops below its threshold, and the engineer for that zone is alerted.
Leak and loss detection - 04
The operator acts
From the control room or a phone, the operator closes the valves around the section, confirming the command before it is sent.
Remote valve control - 05
Confirmed and logged
The controller reports that the valve has moved, and the command is recorded with who sent it and when.
Control room - 06
Reports
Daily, weekly and monthly reports on supply, consumption and losses by zone, for billing, compliance and reviews.
Reports
The modules
Start with the ones you need and add the rest later, on the same platform and the same hardware.
Remote valve control
Motorised actuators fitted to the valves already in the network, so they can be opened, closed and scheduled remotely, with each valve’s state shown on the platform.
Network monitoring
Flow, pressure, level and water quality measured across the network, around the clock.
Leak and loss detection
Unusual flow and pressure flagged as they happen, with thresholds set per sensor, so leaks, bursts and theft can be found early.
Pump and reservoir automation
Pumps started and stopped by level or on a timetable, and reservoirs kept within their limits, with timed supply to each zone.
Network map
Pipes, valves, supply zones and readings on a GIS map of the network.
Control room
One view of the sites for the operations team, with alerts, trends and the controls to act on them, and a record of every command.
Metering
The SIWaM meter measures quantity, quality and pressure at the connection, for billing by measured use and early warning of leaks.
Reports
Trends by day, week and month, and zone-by-zone comparison to locate losses.
In IoTyX
What the hardware measures
Readings arrive in IoTyX as they are taken: on the web, on a phone and on the control room wall.
- Reservoir and tank levels
- Flow and pressure
- Water quality
- Valve position
- Pump state and running hours
- Consumption at each connection
Before you start
What is worth knowing before a project begins.
- A valve that is seized or damaged is repaired before an actuator is fitted to it.
- Each controller needs power and a way to reach the network. Both are planned for each site before installation.
- If a SCADA system already runs part of the network, say so at the start, so the pilot is planned around it.
Questions buyers ask
Ask about your own network, plant or campus. An engineer will reply.
Start a conversation01Do the pipes or valves have to be replaced?
No pipe is replaced. Where a valve is in working order, a motorised actuator is fitted to it and a controller is placed beside it.
02Can operators work from a phone?
Yes. The IoTyX mobile app shows the network and lets authorised operators open or close valves and start pumps. Each command is confirmed before it is sent, and logged.
03What happens if a site loses its connection?
The controller keeps its readings while the connection is down and sends them when it returns.
04Who can see and operate what?
Access is set by role. Administrators, engineers and operators each see the sites and zones they are responsible for, and only authorised people can send commands. Assets can also be shared with a contractor or partner.
05Where is the data kept?
IoTyX stores its data in India. For government projects it can also run on dedicated or on-premise servers.
06How does a project start?
With a conversation about the sites involved, then a demonstration or a pilot on part of the network or site. It is extended to the rest once the pilot has done what it was meant to.
