Start a conversation

Hardware

The boards, actuators and meters in the field.

Ilonnati designs the hardware that connects equipment to IoTyX: a controller beside each machine, actuators for the valves already in the ground, the SIWaM smart water meter, and its own high-voltage products.

Designed in
Hyderabad, India
Runs on
IoTyX, on web and phone
Fits
The equipment already in place
The SIWaM smart water meter: a white housing with brass pipe fittings at top and bottom and the Ilonnati Innovations mark on its face, photographed against water.
The SIWaM smart water meter, made by Ilonnati. A photograph.

In short

Every Ilonnati system starts with hardware in the field. A controller stands beside each machine it runs: its board takes in readings from sensors and meters through its terminals, switches valves and pumps through its relays, and talks to IoTyX over a radio link. Where a valve is to be operated remotely, a motorised actuator is fitted to the valve already there. The SIWaM meter measures quantity, quality and pressure at a connection. Ilonnati also makes its own high-voltage products.

The controller

Boards that connect valves, pumps and sensors in the field to the IoTyX platform. One stands beside each machine it runs.

Ilonnati controller, front elevation with the door openA line drawing of the controller. A rain hood covers the top of the enclosure and an antenna stands on the hood. The door is swung open on its left-hand hinges. Inside, a mounting plate carries a power supply and two breakers on a rail at the top and, below them, the controller board: a processor, a radio module wired up to the antenna, a bank of four relays and a terminal strip along its lower edge. Wires run from the terminal strip down to four cable glands in the base. Twelve numbered balloons point to the parts named in the parts list.123456789101112
Parts list
No.PartWhat it does
1EnclosureStands outdoors, beside the machine it runs.
2Rain hoodCovers the top of the enclosure.
3AntennaCarries the radio link to IoTyX.
4Cable glandsBring the cables in from the machine and its sensors.
5Mounting plateCarries the board, the power supply and the breakers.
6Power supplyPowers the board.
7BreakersProtect the incoming supply.
8Controller boardMade by Ilonnati. Connects the machine to IoTyX.
9Terminal stripTakes in the sensors.
10ProcessorPasses readings to the radio, and commands to the relays.
11Radio moduleSends readings to IoTyX and receives its commands.
12RelaysSwitch the valve or pump.
Figure1
TitleIlonnati controller
ViewFront elevation, door open
ScaleNot to scale
The controller with its door open. Red marks the enclosure and the board. A technical illustration, not to scale.

What the board does

A simulated example, from a sensor reading to a valve opening.

  1. TerminalsSensor reading in
  2. Sent to IoTyX
  3. Command received: open valve
  4. RelaysRelay closed, valve opening

On a valve already in the ground

Motorised actuators fitted to the valves already in the network, so they can be opened, closed and scheduled remotely, with each valve’s state shown on the platform.

Motorised actuator fitted to an existing valveA line drawing of a valve on a flanged pipe, seen from the side. The pipe, its flanged joints, the valve body and the valve stem, drawn in navy, were already in place. Drawn in red, Ilonnati fits a mounting bracket on top of the valve, a coupling onto the stem and a motorised actuator on the bracket, with a cable running from the actuator to an Ilonnati controller standing nearby. Nine numbered balloons point to the parts named in the parts list, which groups them into what was already in place and what Ilonnati fits.123456789
Parts list
No.PartWhat it does
Already in place
1PipeStays as it is: no change to the pipes.
2Flanged jointThe valve’s joint to the pipe, left untouched.
3Valve bodyThe valve already in the network.
4StemOpens and closes the valve, now turned by the actuator.
Fitted by Ilonnati
5Mounting bracketHolds the actuator on the valve.
6CouplingJoins the actuator to the stem.
7Motorised actuatorOpens and closes the valve remotely, on command or on a schedule.
8CableConnects the actuator to the controller.
9Ilonnati controllerLinks the valve to IoTyX, where its state is shown.
Figure2
TitleMotorised actuator on an existing valve
ViewElevation
ScaleNot to scale
A motorised actuator on an existing valve, wired to a controller. Red marks what Ilonnati fits; the rest was already there.

SIWaM smart water meter

Measures, monitors and manages the quantity, quality and pressure of water in the system.

SIWaM smart water meter, front elevation on a pipeA line drawing of the meter fitted in line with a vertical pipe. The housing has a raised cap at the top, two round lugs at its upper corners, a face plate on its front, a seam across the middle and a rounded lower body with a small catch at the bottom. A threaded connection at each end joins it to the pipe. The communication module is drawn as a dashed outline inside the housing. Four numbered balloons point to the parts named in the parts list.1234
Parts list
No.PartWhat it does
1BodyThe meter’s housing, fitted in line with the pipe.
2Pipe connectionsThreaded, one at each end of the meter.
3Face plateCarries the Ilonnati mark.
4Communication moduleInside the housing, shown dashed. Not tied to one communication network.
The meter on a vertical, a horizontal and a sloping pipe

Fits on a pipe at any angle.

Figure3
TitleSIWaM smart water meter
ViewFront elevation
ScaleNot to scale

What it does

  • Detects theft, leakage, pipe bursts and tampering as they happen
  • Controls flow remotely
  • Samples water quality automatically, at set intervals
  • Fits on a pipe at any angle
  • Demand forecasts over the short, medium and long term
  • Not tied to one communication network
  • 90% of components of Indian origin, designed and developed in India

Where it is used

  • Drinking water quality

    Quality sampled automatically where drinking water is supplied.

  • Inlet water use

    Water measured as it enters a building, a plant or a community.

  • Commercial buildings

    Use accounted for by tenant, and leaks shut off inside the building.

  • Rural, urban and smart city supply

    Quantity, quality and pressure across a supply network.

SIWaM

Smart water meter

  • Patent application filed in India: Smart Intelligent Water Monitoring, No. 202241033836, June 2022
  • Registered trademarks: Ilonnati Innovations, and SIWaM as SIWAM

In production

High-voltage hardware

Ilonnati’s own high-voltage products, in production today. Ask for the details of the range, and an engineer will send them with what fits your requirement.

Questions buyers ask

Not answered here?

Ask about your own network, plant or campus. An engineer will reply.

Start a conversation
01Can the actuators fit our existing valves?

Where a valve is in working order, a motorised actuator is fitted to it with a bracket and coupling and wired to a controller beside it. A seized or damaged valve is repaired first.

02What does a controller connect to?

Sensors and meters through its terminals, valves and pumps through its relays, and IoTyX through its radio.

03Where is the hardware designed?

In Hyderabad. 90% of the SIWaM meter’s components are of Indian origin.

04Is there a patent?

Ilonnati has filed a patent application in India for Smart Intelligent Water Monitoring (No. 202241033836, June 2022), which is under examination. SIWAM is a registered trademark.

05What are the high-voltage products?

Ask for the details: an engineer will send them, with what fits your requirement.

06Can Ilonnati build hardware to our requirement?

Yes. When a client needs something that is not on the shelf, Ilonnati designs the hardware and the software to the requirement, and delivers both.

Start a conversation

Tell us what you need to connect, monitor or control